Production Failure: Product Quality Control Review as a Potential Research Activity and Community Service

Kegagalan Produksi: Review Pengendalian Kualitas Produk Sebagai Satu Potensi Aktivitas Riset dan Pengabdian Masyarakat

  • Emma Budi Sulistiarini Universitas Widyagama Malang
  • Alfiana Alfiana Universitas Widyagama Malang
  • Nurida Finahari Universitas Widyagama Malang

Abstract

Production control is an important aspect in a company. Control management is carried out as an effort to reduce and prevent product failures or defects. The purpose of writing this article is to review production failures through product quality control. The results of the review can be used as a situational analysis study for community service activities, especially for industrial engineering. The review is carried out by searching the literature for national publications over the last 10 years. The summary of the research is carried out by grouping based on the category of control method used, the field of study or product being studied and the results of the research. The results of the analysis show that the FMEA (Failure Mode and Effect Analysis) method is widely used in case studies in manufacturing companies. Further research can be carried out to compare the application of the method to similar case studies. Community service activities in this field can be directed to implement the FMEA method for target partners for types of businesses that carry out production processes, goods, and services.

Downloads

Download data is not yet available.

Author Biographies

Emma Budi Sulistiarini, Universitas Widyagama Malang

Prodi Teknik Industri

Alfiana Alfiana, Universitas Widyagama Malang

Prodi Manajemen

Nurida Finahari, Universitas Widyagama Malang

Prodi Teknik Mesin

References

[1] M. C. Azhari and E. R. Pribadi, “Analisis Faktor Penyebab Kegagalan Produk Box Mapela Hasil Mesin Injeksi Plastik,” Jurnal Online Sekolah Tinggi …, vol. 15, no. 1, pp. 27–39, 2020.
[2] E. Y. Arifianto and R. N. Briliana, “Identifikasi Penyebab dan Analisis Risiko Kegagalan Proses Produksi Geomembrane Pabrik Plastik Menggunakan Pendekatan FMEA,” Seminar Nasional Teknik dan Manajemen Industri, vol. 1, no. 1, pp. 66–72, 2021, doi: 10.28932/sentekmi2021.v1i1.69.
[3] A. Rahman and F. Fahma, “Penggunaan Metode Fmeca (Failure Modes Effects Criticality Analysis) Dalam Identifikasi Titik Kritis Di Industri Kemasan,” Jurnal Teknologi Industri Pertanian, vol. 31, no. 1, pp. 110–119, 2021, doi: 10.24961/j.tek.ind.pert. 2021.31.1.110.
[4] A. P. Pambudy, “Pengaruh Pengendalian Produksi Terhadap Kegagalan Produk Songkok Pada Ud. Cahaya Bintang Pandantoyo Kalitengah Kabupaten Lamongan,” Jurnal Ekbis, vol. 17, no. 1, p. 12, 2017, doi: 10.30736/ekbis.v17i1.72.
[5] N. Badariah, D. Sugiarto, and C. Anugerah, “Penerapan Metode Failure Mode and Effect Analysis ( FMEA ) dan Expert System (Sistem Pakar),” Jurusan Teknik Industri Fakultas Teknologi Industri Universitas Trisakti, vol. 1, no. November, pp. 1–10, 2016.
[6] D. P. Sari, Z. F. Rosyada, and N. Rahmadhani, “Analisa Penyebab Kegagalan Produk Woven Bag Dengan Menggunakan Metode Failure Mode and Effects Analysis (Studi Kasus Di Pt Indomaju Textindo Kudus),” Prosiding SNST Fakultas Teknik, vol. 1, no. 1, pp. 6–11, 2011.
[7] R. Saputra and D. T. Santoso, “Analisis Kegagalan Proses Produksi Plastik Pada Mesin Cutting Di Pt. Fkp Dengan Pendekatan Failure Mode and Effect Analysis Dan Diagram Pareto,” Barometer, vol. 6, no. 1, pp. 322–327, 2021, doi: 10.35261/barometer. v6i1.4516.
[8] N. B. Puspitasari and A. Martanto, “Analisis Kecelakaan Kerja Dengan Metode Failure Mode And Effect Analysis (FMEA) Studi Kasus : Automotive Workshop Semarang,” Jurusan Teknik Industri Fakultas Teknologi Industri Universitas Trisakti, vol. 1, no. 1, pp. 1–7, 2014.
[9] Y. Alfianto, “Analisis Penyebab Kecacatan Produk Weight A Handle Menggunakan Metode Fault Tree Analysis dan Failure Mode and Effect Analysis sebagai Rancangan Perbaikan Produk,” JIEMS (Journal of Industrial Engineering and Management Systems), vol. 12, no. 2, pp. 71–80, 2019, doi: 10.30813/jiems.v12i2.1493.
[10] R. Y. Prasetya, S. Suhermanto, and M. Muryanto, “Implementasi FMEA dalam Menganalisis Risiko Kegagalan Proses Produksi Berdasarkan RPN,” Performa: Media Ilmiah Teknik Industri, vol. 20, no. 2, p. 133, 2021, doi: 10.20961/performa. 20.2.52219.
[11] Suhartini and Z. Djefrianto, “Analisa Risiko Kegagalan Proses Produksi di PDAM dengan Metode Fuzzy FMEA,” Proceeding Industrial Design National Seminar, no. September, pp. 978–979, 2013.
[12] A. S. Umartono and S. Awali, “Analisa Kegagalan Proses Heat Treatment Baja Sup-9 Pada Pembuatan Pegas Daun,” Wahana Teknik, vol. 04, no. Juni, pp. 55–75, 2015.
[13] N. W. A. S. Dewi, S. Mulyani, and I. W. Arnata, “Pengendalian Kualitas Atribut Kemasan Menggunakan Metode Failure Mode Effect Analysis (FMEA)Pada Proses Produksi Air Minum Dalam Kemasan,” Jurnal Rekayasa Dan Manajemen Agroindustri, vol. 4, no. 3, pp. 149 – 160, 2016.
[14] Angga. Pratama, E. W. Asih, and P. Wisnubroto, “Analisis Penyebab Kecacatan Wreapper Pada Mesin Single Flowrap (Sfw) Menggunakan Metode Failure Mode Effect and Analysis (Fmea) & Fault Tree Analysis (Fta) Pada Pt. Nestle Indonesia,” Jurnal REKAVASI, vol. 4, no. 2, pp. 60–118, 2016.
[15] A. Daru D and S. Purnomo, “Usulan Tindakan Dalam Upaya Mengurangi Potensial Couses Kegagalan Proses Produksi Pada CV Trijaya Mulia,” in Seminar Nasional Inovasi Dan Aplikasi Teknologi Di Industri. ITN Malang 4 Februari 2017, 2017, p. C5.1-6.
[16] W. Septiani, B. H. Perdana, and J. Saragih, “Perancangan Sistem Pakar Berbasis Fmea Untuk Mengidentifikasi Dan Mendiagnosis Risiko Kegagalan Proses Pada Proses Produksi Rear Combination E83 Truk Hino Dutro,” Jurnal Ilmiah Teknik Industri, vol. 5, no. 3, pp. 164–170, 2018, doi: 10.24912 /jitiuntar.v5i3.2104.
[17] I. Masrofah and H. Firdaus, “Analisis Cacat Produk Baju Muslim Di Pd. Yarico Collection Menggunakan Metode Failure Mode And Effect Analysis,” Jurnal Media Teknik dan Sistem Industri, vol. 2, no. 2, p. 43, 2018, doi: 10.35194/jmtsi.v2i2.404.
[18] C. D. Putra, A. Syarief, and H. Isworo, “Analisa Kegagalan Menggunakan Metode Failure Mode and,” vol. 3, no. 1, pp. 33–42, 2018.
[19] S. Imam and D. M. N. Pakpahan, “Risiko Kegagalan Pada Proses Produksi Kemasan Karton Lipat (Studi Kasus : PT. Interact Corpindo),” Journal Printing and Packaging Technology, vol. 1, pp. 49–55, 2020.
[20] I. N. Putri, “Analisis Risiko Kegagalan Produk Mempengaruhi Kualitas Pelayanan Menggunakan House Of Risk Dan Supply Chain Operations Reference,” Jurnal Optimasi Teknik Industri (JOTI), vol. 2, no. 1, p. 19, 2020, doi: 10.30998/joti.v2i1.4049.
[21] M. T. Hidayat and R. Rochmoeljati, “Perbaikan Kualitas Produk Roti Tawar Gandeng Dengan Metode Fault Tree Analysis ( FTA ) Dan Failure Mode And Effect Analysis ( FMEA ) Di Pt . XXZ,” Juminten: Jurnal Manajemen Industri dan Teknologi, vol. 01, no. 04, pp. 70–80, 2020.
[22] D. P. Pradana, S. Rahayuningsih, and H. B. Santoso, “Analisis Rejected Produk Dalam Proses Return Di PT. Gunawan Fajar Menggunakan Metode FMEA,” JURMATIS : Jurnal Ilmiah Mahasiswa Teknik Industri, vol. 2, no. 1, p. 44, 2020, doi: 10.30737/jurmatis. v2i1.863.
[23] S. Nurfadillah, K. Budiraharjo, and W. Roessali, “Prioritas Dan Strategi Penanganan Risiko Produksi Pada Industri Tahu Di Kabupaten Grobogan,” Agritech: Jurnal Fakultas Pertanian Universitas Muhamma-diyah Purwokerto, vol. 22, no. 1, 2020, doi: 10.30595/agritech.v22i1.7504.
[24] A. Pibisono, S. Suprapto, and R. Ahya, “Analisis Kegagalan Maintenance Unit Produksi Menggunakan Metode FMEA dan FTA di PT. Saptaindra Sejati,” Jurnal Aplikasi Ilmu Teknik Industri (JAPTI), vol. 1, no. 2, pp. 1–10, 2021.
[25] A. Basuki and I. Chusnayaini, “Identifikasi Resiko Kegagalan Proses Penyebab Terjadinya Cacat Produk dengan Metode FMEA-SAW,” Matrik, vol. 22, no. 1, p. 37, 2021, doi: 10.30587/matrik.v22i1.1967.
[26] A. Lestari and N. A. Mahbubah, “Analisis Defect Proses Produksi Songkok Berbasis Metode FMEA Dan FTA di Home - Industri Songkok GSA Lamongan,” Jurnal Serambi Engineering, vol. 6, no. 3, 2021, doi: 10.32672/jse.v6i3.3254.
[27] A. Hernawan and N. A. Mahbubah, “Integrasi Statistical Process Control dan Failure Mode And Effect Analysis Guna Meminimalisasi Defect Pada Proses Produksi Pipa PVC,” Jurnal Engine: Energi, Manufaktur, dan Material, vol. 5, no. 2, p. 65, 2021, doi: 10.30588/jeemm.v5i2.906.
[28] A. Syarifudin and J. T. Putra, “Analisa Risiko Kegagalan Komponen Pada Excavator Komatsu 150LC Dengan Metode FTA Dan FMEA Di PT . XY,” vol. 4, no. 2, pp. 1–10, 2021.
[29] B. A. Nainggolan, L. Mei, and C. Wulandari, “Analisis Risiko Operasional Menggunakan Metode FMEA di CV. Gamarends Marine Supply Surabaya,” Prosiding Seminar Nasional Riset dan Teknologi Terapan, no. 2020, pp. 1–13, 2021.
[30] M. Fathurrozi, E. Ismiyah, and Moh. Jufriyanto, “Pada Produk Sopak Mengguna-kan Metode Failure Mode And Efect Analysis,” vol. 9, no. 2, pp. 195–209, 2021.
[31] D. Lowrenza, “Identifikasi Faktor Kegagalan Hasil Produksi Busa dengan Sistem Pakar Metode Dempster Shafer dan Certainty Factor,” Jurnal Informatika Ekonomi Bisnis, vol. 4, pp. 1–6, 2022, doi: 10.37034/ infeb.v4i1.105.
Published
2022-12-07
How to Cite
SULISTIARINI, Emma Budi; ALFIANA, Alfiana; FINAHARI, Nurida. Production Failure: Product Quality Control Review as a Potential Research Activity and Community Service. JATI EMAS (Jurnal Aplikasi Teknik dan Pengabdian Masyarakat), [S.l.], v. 7, n. 1, p. 1-8, dec. 2022. ISSN 2550-0821. Available at: <https://journal.fdi.or.id/index.php/jatiemas/article/view/709>. Date accessed: 01 feb. 2023. doi: https://doi.org/10.36339/je.v7i1.709.